Are there any problems with the Onkyo receivers?

Problems With Onkyo Receivers 1 No Sound. Incorrect settings on your Onkyo receiver can result in no sound. 2 No Picture. Video connections going into your Onkyo receiver must be securely seated in the video inputs before you will see a picture. 3 Cannot Control Other Components. 4 Cannot Record. …

How to fix Onkyo TX sr606 and SR607 HDMI input problem?

How to fix your Onkyo when the HDMI input takes, 2, 5, 10, 20 minutes to show up on your TV. Or it maybe doesn’t work at all with the HDMI inputs. NOTICE: The DigiKey part number is obsolete. The new & better part is 493-2141-1-ND NOTICE: The SR607 is almost identical to the SR606, so this procedure will also work to fix the problem. Loading…

Can you use IR remote control on Onkyo?

My Onkyo AV receiver TX-DS989 does not work with IR remote control (The remote control is OK while the inside IR Receiver is broken). I would like to use a standard IR receiver connected to the “IR IN MAIN ” on the back in order to use again the remote control.

Why does my Onkyo 7.2 surround sound shut off?

Reconnect them one at a time and turn the receiver on. When you connect the bad wire or speaker the receiver will shut down. If after you connect them all if the receiver now stays on then there was a short where the wires were connected to the receiver that you repaired when you replaced them.

How many speakers are in the Onkyo tx-sr875 surround sound receiver?

There are nine sets of speaker terminals. Seven of them are for the 7.1-channels in the main system. The other two may be used for Zone 2. If you’re using zone 2 and have a 7.1-channel setup in your main system, the latter is restricted to 5.1-channels if Zone2 is operating.

Why does my Onkyo surround sound not work?

If you have turned B “on” the receiver shuts down the surround channels. If that isn’t the problem, make sure none of the speakers are actually wired into speaker B on the back panel. That was it after I read the manual last night going through all connections etc.

What kind of decoding does the Onkyo do?

In addition to the usual multichannel Dolby Digital and DTS modes, the Onkyo provides decoding for those high resolution, lossless audio modes mentioned earlier if it receives them in raw bitstream mode.

What should the impedance be for a Onkyo bridged speaker?

Bridging amps increases power output, sometimes dramatically, but it also makes the resulting combined amps very sensitive to low impedances. Onkyo warns against using speaker loads lower than 8 ohms in bridged mode. Onkyo does not recommend nominal speaker impedances of less than 4 ohms under any circumstances.

How can I unplug my Onkyo headphones?

Unplug headphones from the receiver when you are trying to use your system with the external speakers. Press the “Muting” button on the remote control to unmute your Onkyo receiver. Check the inputs and outputs to ensure they are correctly connected to the receiver.

When did Onkyo start making phonograph pickups?

Onkyo began making phonograph pickups in 1946. As of 2010, the company is still making audio components. Onkyo is known for their receivers, which enable other stereo or home theater components to work together to provide you with a complete listening and viewing entertainment experience.

What is the latest firmware version of onkyo?

System firmware version: 74　/　Cast firmware version: 1.44.219548 22 December 2020 TX-NR696 Firmware Number: R122-0808-1140-0029 TX-NR797

Why are my Onkyo receivers not working properly?

As part of our commitment to quality and customer service we have determined that a limited number of Onkyo Brand receivers manufactured between 2009 and 2012 may experience loss of audio or loss of network connection. This malfunction has been traced back to a defective network chip.

How to fix no sound coming out of the AV receiver?

Contact onkyo and they should help you by fixing the broken part. Normally if its a onboard chip as i’m assuming it is, they are almost impossible to fix without expensive tools. Contact them and see what they can do, if they cant do anything, let me know and ill give you another option.

Is there a problem with the Onkyo tx-nr609?

Has anyone had this problem and were they able to resolve it. They have done this for a While, the 6 Series onkyo’s have been poor since the 609. We have had many Issues including your fault many Times over. You will have to send it to genserve for Repair! It’s a board they Replace but can’t remember which one.

Which is the best soldering iron for Onkyo?

Electrolytics are notorious for this sort of behaviour (especially if under specified – Onkyo clearly penny pinching). 100uf 105c 25v ones are available for a few £ on Ebay, so if you are prepared to get stuck in with the soldering iron this could be a quick/cheap solution (mine is outside warranty).

How can I get my Onkyo headphones to work?

Why is no sound coming out of my AV receiver?

No sound coming out from the receiver. I saw a solution on youtube which suggested that if you heat a particular chip for few minutes, it starts working. I used hair dryer to do that. It worked for me for few minutes but the again no sound. Answered! View the answer I have this problem too Is this a good question?

Can a PC Hook Up to an Onkyo TV?

You can also use an HDMI audio extractor to provide a digital audio output from the PC. That will let you connect the PC to the TV directly with HDMI and to the receiver with digital audio. You must log in or register to reply here. New Android TV Box Not supported by Onkyo Receiver, But old (1.5-2 years) box is> why? Solved!

How can I Unmute my Onkyo remote control?

Press the “Muting” button on the remote control to unmute your Onkyo receiver. Check the inputs and outputs to ensure they are correctly connected to the receiver. Adjust the volume controls so you can hear sound.

What makes Onkyo tx-nr737 home theater receiver so good?

The ‘NR737 is about more than just convenience and versatility. Onkyo has always put a premium on sound quality. This receiver features their Wide Range Amplifier Technology, which provides plenty of current to ensure smooth sound even during large swings in dynamics.

How much does Onkyo tx-nr509 AV receiver cost?

Onkyo TX-NR509 Onkyo has a reputation of delivering quality performance at competitive prices. The new 5.1 channel Onkyo TX-NR509retails for less than $400 and is packed with features usually found in more expensive receivers. It is network-enabled, hence the ‘NR’ moniker, and is also designed to be iPod/iPhone friendly. Onkyo TX-NR509

Why is my Onkyo tx-nr609 suddenly no sound?

The loaned tx-nr616 has now started to become intermittent on start up for dislaying images to the tv. Looks like the hdmi board is starting to fail on this one now. Spoke to richer sounds and they will give me another loan machine. Still no parts available for the tx-nr609

Is the Onkyo tx-8050 compatible with Windows 7?

All Onkyo network receivers are also compatible with Microsoft’s Windows® 7 platform, which includes the DLNA 1.5-specified “Play To” media-streaming feature so you can easily stream music store on PCs connected to your home network. This internet connectivity has the added benefit of making firmware updates simpler than ever.

What is the name of the 2011 Onkyo receiver?

It is network-enabled, hence the ‘NR’ moniker, and is also designed to be iPod/iPhone friendly. The 2011 Onkyo receivers are redesigned and comes with a more industrial looking black fascia that may not go down well with previous Onkyo owners.

Is there a problem with my Onkyo tx-nr509?

– YouTube I cant hear any sound and it just happened one day? I cant go forward in the Audyssey calibration-setup? what to do? I cant hear any sound and it just happened one day? I cant go forward in the Audyssey calibration-setup? what to do?

What to do if your Onkyo tweeter shuts off?

Can test a tweeter if its blown by moving your hand over it. If there’s no change in sound then its blown. If the receiver is shutting off just by selecting inputs then you’ll need to see if you can get it repaired. Keep your receipt?

Is it safe to buy Onkyo tx-nr616 again?

Will not buy Onkyo again and advise others not to do so. Would you believe it. The loaned tx-nr616 has now started to become intermittent on start up for dislaying images to the tv. Looks like the hdmi board is starting to fail on this one now. Spoke to richer sounds and they will give me another loan machine.

How can you Hard Reset an Onkyo texas-nr708-hardware?

Reset the processor of the Onkyo by following the steps below: To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/ DVR, press ON/ STANDBY.

Where are the optical audio lines on the Onkyo?

The Onkyo has 2 optical audio lines in in the back. When I hit the “digital input” button on the front of receiver, I can select from OPT1, OPT2, or COAX. I currently have the optical audio line going into OPT2, but if I select OPT2, I hear no sound.

Are there any problems with the Onkyo receivers?