How do you connect a Bose 901 speaker to an amplifier?
Samuel Coleman
Published May 07, 2026
How do you connect a Bose 901 speaker to an amplifier?
1. Choose the best locations and support for the 901 speakers (page 6). 2. Connect the speakers to the amplifier or receiver (page 8). 3. Connect the 901 active equalizer to the amplifier or receiver using either the TAPE MONITOR or PRE AMP OUT/MAIN AMP IN connections (page 9). 4.
Can a Bose 901 Series VI be used without an equalizer?
The use of 901 Series VI speakers without the 901 Series VI active equalizer will result in improper per- formance. The use of graphic or parametric equalizers, instead of the Bose 901 equalizer, will result in unsatisfactory performance.
Where are the serial numbers on the Bose 901?
Please write them on your warranty card and in the spaces provided on page 2. The serial num- bers are located on the bottom of the 901 speakers and on the back of the equalizer. WARNING: Each speaker carton weighs over 35 lb (16 kg). Use good lifting practice to avoid injury.
How do you connect a Bose equalizer to an amplifier?
If you’re using the equalizer in a home theater setup, connect this end of the cable to the “Main Amp In” jacks on your receiver or amplifier. Connect the Bose 901 equalizer’s power cord to one of the switched power outlets on your receiver or amplifier.
Can a Bose 901 be used as a receiver?
They still make both stereo integrated amps and receivers. The 901s are not terribly efficient, so make sure your replacement has at least as much power as your old Quadraflex. You need either a tape loop (tape monitor function) or pre-outs and main amp inputs. It is refurbished, but I have had great success with their refurbished gear.
Do you need a tape loop for a Bose 901?
You can get one of these Yamaha’s new from Newegg for $450 shipped if you are too worried about the refurbs. Kurt makes a good point – I forgot about the 901’s outboard equalizer. If you’re using it, you’ll definitely need a receiver with a tape loop, or one with jacks for preamp out / amp input.
Is the Bose 2160 an old school receiver?
The 2160 is an old school style receiver with some modern touches…the amp section would rival many 2 ch power amps. I was considering the older model of this to power my zone 2 & 3, but the connectivity to the pre/pro made it a lot more challenging than I was willing to deal.
Why does my Bose 901 play low frequency music?
And third was the poor bass response (after series 3). In today’s world adding a subwoofer is the most obvious way to deal with this. In a Bose store, you will notice the music they select to play on the 901’s (and probably throughout the store) is mostly midrange with very little content at either the high or low frequencies.
1. Choose the best locations and support for the 901 speakers (page 6). 2. Connect the speakers to the amplifier or receiver (page 8). 3. Connect the 901 active equalizer to the amplifier or receiver using either the TAPE MONITOR or PRE AMP OUT/MAIN AMP IN connections (page 9). 4.
Is the Bose 901 Series VI direct / reflecting?
Thank you for purchasing the Bose®901®Series VI Direct/Reflecting®speakers. They represent the best in Bose Corporation speaker design and engineering and will give you many years of listening pleasure. The installation and operating principles of this system are significantly different from those of conventional speakers.
Where is the Bose 901 active equalizer located?
The 901 active equalizer is most commonly connected to the tape monitor connections on the receiver. If you plan to connect a tape recorder, use the set of inputs and outputs located on the back of the 901 active equalizer marked TAPE RECORDER CONNECTIONS.
The 901 active equalizer is most commonly connected to the tape monitor connections on the receiver. If you plan to connect a tape recorder, use the set of inputs and outputs located on the back of the 901 active equalizer marked TAPE RECORDER CONNECTIONS.
Thank you for purchasing the Bose®901®Series VI Direct/Reflecting®speakers. They represent the best in Bose Corporation speaker design and engineering and will give you many years of listening pleasure. The installation and operating principles of this system are significantly different from those of conventional speakers.
Can a Bose 901 be used as an AVR?
The Bose 901 is a nifty speaker but their mandatory use of an equalizer makes them a bad choice for AVRs. Here’s a copy of your owners manual.
Does Bose still make 901?
Also of interest, the Bose 901 has been in continuous production since 1968 second only to the Klipsch Klipschorn speaker in longevity of continuous production. [21] Bose ended production of the Bose 901 loud speaker with series VI on September 2016. I received this information from The Bose Corporation.
Did Bose discontinue 901?
Bose, recently discontinued the 901 without a peep. No press release, nothing after 49 years of production. Word on the forums says they’ve gone out of production in favor of a new technology, but who knows what that is.
Is Bose 901 still made?
Posted February 21, 2018 (edited) I just learned that the Bose 901 is no longer being made available from Bose Corporation. This would be the end of a glorious 50-year run for this fine old speaker, and it’s probably safe to say that if founder Amar Bose were still alive, no one would dare discontinue this model regardless of low the sales volume!
Are Bose 901 speakers discontinued?
Unlike other Bose speakers, the 901 Series was not intended to be used without their included 901 Active Equalizer. While the speakers included metal pedestal stands, ceiling mounts were also available. It was sold until 2016, when the 901 Series VI was discontinued.