How to fix no sound and digital blinking on my pioneer?

How to fix no sound and digital blinking on my pioneer?

Disconnect then reconnect the HDMI cable between the Cable Box and the Pioneer receiver, making sure it is secure on both ends. Then plug the Cable Box back into power and once rebooted turn everything back on and select the CBL Input on the Pioneer. The sound should be restored and the Digital light no longer blinking.

Is the vsx-523-k with HDMI no sound?

Pioneer receiver vsx-523-k with HDMI has vider but no sound. Pioneer receiver vsx-523-k with HDMI has vider but no sound. I removed HDMI from SAT/CABLE (DirectTV)…

Where is the enter button on a pioneer receiver?

On Pioneer receivers, you unplug the unit, fully powering it down. Plug it back in, but do not power it up yet. On the front panel, find the button marked “Enter”. Depending on unit, this may be a single isolated button or a bar type button along a line of such bars.

Where is the HDMI cable on a pioneer TV?

These are mostly at the back of the top HDMI board on most Pioneer units. If you remove the top cover (side and back screws hold it on, then lift the back up, and pull up and out toward the back), you will see the top board. You will see one HDMI cable going frontwards.

What kind of inputs does the pioneer VSX 521 have?

You get four 3D-friendly HDMI 1.4a inputs — one more than the even cheaper VSX-421 — plus two component, four phono AV, two analogue stereo and three digital audio (two optical) inputs. The Pioneer VSX-521 looks more expensive than it is.

Disconnect then reconnect the HDMI cable between the Cable Box and the Pioneer receiver, making sure it is secure on both ends. Then plug the Cable Box back into power and once rebooted turn everything back on and select the CBL Input on the Pioneer. The sound should be restored and the Digital light no longer blinking.

These are mostly at the back of the top HDMI board on most Pioneer units. If you remove the top cover (side and back screws hold it on, then lift the back up, and pull up and out toward the back), you will see the top board. You will see one HDMI cable going frontwards.

Why does my pioneer TV not work with Apple TV?

The fact that the receiver works fine with the Apple TV, and not the Cable indicates the Cable Box- and is a problem I see daily. Shut the receiver off, then unplug the Cable Box from power. Disconnect then reconnect the HDMI cable between the Cable Box and the Pioneer receiver, making sure it is secure on both ends.

How to fix sound issue in Pioneer stereo receiver?

How to fix sound issue in Pioneer Stereo receiver? when i turn the volume knob sometimes the sound keeps going on and off. Please help. Is this a good question? a few more informations would make it easier to answer this.

The fact that the receiver works fine with the Apple TV, and not the Cable indicates the Cable Box- and is a problem I see daily. Shut the receiver off, then unplug the Cable Box from power. Disconnect then reconnect the HDMI cable between the Cable Box and the Pioneer receiver, making sure it is secure on both ends.

Why is the O2 Jack not working on my pioneer?

The receiver should be defaulting back to “A” because that is “Analog” which is what those Red and white cables are from the cable box to the receiver. O2 is the “Optical 2” jack, and you’re not using that connection, so what’s happening is the receiver is searching for an audio signal from the Cable Box and not finding one.

Why is my pioneer vsx-52 not working?

If you have a Pioneer VSX-52 all it shows for an Error 1 message is to turn the receiver’s power off, then turn it back on and try updating the software again. Have you verified that the software update is for your particular model as sometimes the device looks for a particular file name when updating and if that is not correct it won’t update.

Why does my pioneer TV have no sound?

The cable box needed to be reset in the first place, but you reset the receiver to factory defaults instead. That is why when you rebooted the cable box, the sound cam through the TV speakers instead of the receiver. So, you need to set the receiver up, just like you did when the unit was brand new.

Why is the digital light blinking on my pioneer?

Then plug the Cable Box back into power and once rebooted turn everything back on and select the CBL Input on the Pioneer. The sound should be restored and the Digital light no longer blinking. 1) Replace the HDMI cable between the cable Box and the receiver.

The receiver should be defaulting back to “A” because that is “Analog” which is what those Red and white cables are from the cable box to the receiver. O2 is the “Optical 2” jack, and you’re not using that connection, so what’s happening is the receiver is searching for an audio signal from the Cable Box and not finding one.

Why does my pioneer HDMI not turn on?

Related issues with HDMI have to do with the quality of the HDMI physical connections. These are mostly at the back of the top HDMI board on most Pioneer units. If you remove the top cover (side and back screws hold it on, then lift the back up, and pull up and out toward the back), you will see the top board.

What should the operating environment be for a vsx-50?

D3-4-2-1-7b*_A1_En Operating Environment Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light) D3-4-2-1-7c*_A1_En

Related issues with HDMI have to do with the quality of the HDMI physical connections. These are mostly at the back of the top HDMI board on most Pioneer units. If you remove the top cover (side and back screws hold it on, then lift the back up, and pull up and out toward the back), you will see the top board.

D3-4-2-1-7b*_A1_En Operating Environment Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light) D3-4-2-1-7c*_A1_En

On Pioneer receivers, you unplug the unit, fully powering it down. Plug it back in, but do not power it up yet. On the front panel, find the button marked “Enter”. Depending on unit, this may be a single isolated button or a bar type button along a line of such bars.