Is the scantronic 9800 alarm system in place?

Just moved into a house and we have a Scantronic 9800 alarm system in place. The PIRs etc are all working, but the keypad in the hallway is dead – no LEDs displaying at all. Also, we do not have codes etc for this system, but it may just be a bettery issue or something simple.

How does the 9800 alarm control panel work?

Introduction The 9800 Alarm Control Panel comprises a control unit in a shielded case, and up to four separate keypads.

What to do if your scantronic alarm goes off?

Open up the panel, switch off the power and disconnect the battery. The external bells may go off at this point if they are SAB types. Unplug the 8 pin EEprom chip and re apply mains power. With the panel still powered up, plug the EEprom back into the board.

What does the 5 R on a scantronic control panel mean?

It is showing the following message “Fault” “Service” & “5 r” Obviously it needs servicing but as we don’t currently have a service contract does anyone know what the 5 r means so that I can tell the service engineer before they come out in case they need some parts.

Introduction The 9800 Alarm Control Panel comprises a control unit in a shielded case, and up to four separate keypads.

What is the factory access code for scantronic 9651?

The control unit loads the factory default access codes: User 1: 1234, Engineer: 7890. Close the control unit and apply mains power. Carry out an engineer reset 1.

Can a permanent tamper alarm arm a mct-302n?

I replaced the battery in an MCT-302n detector and now have a permanent tamper alarm and cannot arm the system. The system doesn’t now … read more Hi I was just reading an old post as have a problem with my visonic powermax plus alarm system.

When did I remove the 9941 keypad from my alarm system?

Discussion in ‘ Electricians’ Talk ‘ started by Graeme Thompson, Jun 2, 2020 . During a decorating binge I removed one of the 9941 keypads from our alarm system (inherited when we bought the house). I’ve reconnected it exactly as it was but now it won’t accept any commands.

Do you need technical support for scantronic intruder alarm?

Scantronic intruder alarm systems are designed to be installed by professional specialist security installers, there is no technical support available for the product for end users. We can also supply a full range of additional intruder alarm parts such as PIR’s, batteries, power supplies, sounders, diallers etc.

How long has scantronic been in the market?

For over 30 years, Scantronic has been recognised internationally for quality, performance and innovation in the field of security systems.

Why is my scantronic 9827 keypad not working?

I powered down the system at the mains (battery was left connected) and connected the 9827 panel. It was all very simple with three wires +0, Sig and +Ve connections. The keypad issued a bleep and the green LEDs which light the keypad buttons, flashed briefly. However I have no display on the keypad.

How do I set up a 9800 battery?

Ensure that the keypad(s) and detectors are securely fitted and their tamper switches closed. 2. Connect the battery and then close the case. 3. Switch on the mains power. Ignore any tones from the internal and keypad sounders. 4. Go to a keypad and key in 1234. 5. Key in 0 followed by 7890 (the default Engineer’s code).

Is the keypad on a scantronic 9800 the same size?

Keypad is almost the same size so minimal making good on decor. Virtually used the same as the 9800 too, so not a major upheaval in use and a nicer LCD screen and alpha numeric zones. Far better than numbers and codes.

How to reset scantronic 9800 alarm system fault codes?

Re connect the battery and enter 07890 into the key pad. Then 99 to exit the engineers mode. You will now need to reset ALL the zone and timing parameters so only do this if you know what you had before. The default user codes will now be 1111 2222 3333 4444 or is it aaaa bbbb cccc dddd (can’t remenber exactly)

Why does my scantronic 9800 make weird noises?

It could be that the keypad is faulty but in general the 9800 is pretty reliable. It might just be that the panel was making weird noises due to a battery fault and the last user disconnected it.

What to do if your scantronic keypad is not working?

Check your book. Oh, and have your code ready and be prepared for the internal sounder/s making a din (or disconnect them temporarily). One way of minimising the external bell sounding time (other than opening it up and disconnecting its battery) is to power the bell from your panel battery.

Is the 9800 keypad the same as the 9600?

Discussion in ‘ Alarms, CCTV & Telephones ‘ started by MADDY2705, 15 Nov 2011 . I have found a 9600 keypad on ebay and it looks the same – can anyone tell me if it is the same kepad as the 9800?

Is the scantronic 9800 alarm system in place?