What does resetting to factory default do?

What does resetting to factory default do?

A factory data reset erases your data from the phone. While data stored in your Google Account can be restored, all apps and their data will be uninstalled. To be ready to restore your data, make sure that it’s in your Google Account. Learn how to back up your data.

What file must be deleted when defaulting a switch factory reset?

To reset these switches to factory defaults, you need to delete the startup configuration and the vlan. dat file.

How do I Reset my Cisco router to factory default?

Find the Reset button on the router. Press and hold the Reset button while you power on the router. Release the Reset button after 10 seconds. Wait 5 to 10 minutes for the router to finish booting.

What is the command to Reset a Cisco switch?

Reset a switch running Cisco IOS Software to factory defaults

1. Enter “enable” mode by typing:
2. The console prompt should change from “switch>” to “switch#” to signify this.
3. To reset the switch to factory default, issue the erase startup-config or write erase command.

How do I reset my 2960 to factory settings?

Reset a Cisco 2960 Switch To Factory Default Settings

1. Connect up your console cable and power on the switch, whilst holding down the “mode” button:
2. Initialize the flash file system with the command: flash_init.

How do I restore to factory settings?

Complete These Steps:

1. Select “System Settings” from the HOME Menu.
2. Scroll down to “System” and select it.
3. Scroll all the way down to the bottom of the menu and select “Formatting Options”.
4. Select “Restore Factory Settings” to delete all data in the system memory.

How do I Reset my Cisco router 1841 to factory settings?

Factory reset a Cisco 1841 router

1. Connect up your console cable and get PuTTY ready on the correct port.
2. Power on the router. As soon as you see iOS loading in PuTTY, right click the top of the PuTTY window and go to Special Commands > Break.
3. The router should now be in rommon mode.

How do I Reset my Cisco 2960 to factory settings?

Reset a Cisco 2960 Switch To Factory Default Settings

1. Connect up a console cable and power on the switch, whilst holding down the “mode” button:
2. Run the following command to initialize the flash file system:
3. Delete the config.text file from the flash directory:

How do you reset a network switch?

Manually Reset the Switch

1. Disconnect all Ethernet cables from the switch.
2. Using a pin, press and hold the Reset button on the switch for 15 to 20 seconds.
3. Once all the port LEDs light up, release the Reset button.
4. Connect your computer directly to the switch using an Ethernet cable.

How to restore factory defaults on Visonic PowerMax?

The factory defaults can be restored by performing a RESET as follows. Remove all power (mains and battery) from the panel. Remove the panel from its backplate place face down on a cushioned surface. The Express needs removal of the internal cover. Identify the two left hand jumper pins marked DEF and fit a jumper across them.

How to fix my Visonic wireless alarm system?

Visionic + system. Performed factory default reset, eliminating Visionic + system. Performed factory default reset, eliminating all zone programming. However, unit reports “Alarm in memory” for about 6 zones and won’t arm. … read more

What is the default user code for Visonic d-302542?

++ [Code] * The factory default master user code is 1 1 1 1. The code is not required if quick arming has been permitted by the installer . Change the factory default code to a secret code without delay (see section 7) Contact list form

How to troubleshoot a visionis access control system?

If everything is setup properly, then verify that the access control system is getting the proper voltage using an ammeter. The maglock has a weird noise while it is operating. Check the access control components, make sure all the wires are properly connected. It may be faulty or have been installed in the wrong way.

Visionic + system. Performed factory default reset, eliminating Visionic + system. Performed factory default reset, eliminating all zone programming. However, unit reports “Alarm in memory” for about 6 zones and won’t arm. … read more

The factory defaults can be restored by performing a RESET as follows. Remove all power (mains and battery) from the panel. Remove the panel from its backplate place face down on a cushioned surface. The Express needs removal of the internal cover. Identify the two left hand jumper pins marked DEF and fit a jumper across them.

If everything is setup properly, then verify that the access control system is getting the proper voltage using an ammeter. The maglock has a weird noise while it is operating. Check the access control components, make sure all the wires are properly connected. It may be faulty or have been installed in the wrong way.

How to restore a legacy Metrologic scanner to its factory?

Note 2: If the scanner is not able to read programming or any other bar codes as a result of wrong configuration, the MetroSet 2 configuration tool should be used to restore the default settings. Download and install MetroSet2.